3.6 V Fiber Optics - Transceivers 10

Reset All

Part	Manufacturer	Fiber Optic Type	Mounting Feature	Maximum Supply Voltage	Terminal Finish	Maximum Operating Temperature	Minimum Operating Temperature	Rx Data Rate	Tx Data Rate	Emitter or Detector Type	Fiber Type	Nominal Optical Power Output	Connection Type	Nominal Supply Voltage	Body Length/Diameter	Body Width	Package Style (Meter)	Sub-Category	Body Height	Nominal Operating Wavelength	Minimum Supply Voltage	Minimum Operating Wavelength	Communication Standard	Maximum Operating Wavelength	Additional Features	JESD-609 Code	Built-in Features
AFBR-5972Z	Broadcom	TRANSCEIVER	PANEL MOUNT	3.6 V		85 Cel	-40 Cel	100 Mbps	100 Mbps	LED, PIN PHOTODIODE	POF	.223 mW		3.3 V	21.45 mm	15.9 inch		Fiber Optic Transceivers	11.9 mm	650 nm	3 V	635 nm		675 nm	IT ALSO OPERATES WAVELENGTH FROM 635 NM TO 675 NM		AMPLIFIER
AFBR-59E4APZ	Broadcom	TRANSCEIVER	PANEL MOUNT, THROUGH HOLE MOUNT	3.6 V	TIN	85 Cel	-40 Cel			LED, PIN PHOTODIODE	50/125, 62.5/125, MMF	.02 mW	LC CONNECTOR	3.3 V	48.19 mm	13.59 inch	DIP		9.8 mm	1308 nm	3 V	1270 nm		1380 nm	IT ALSO HAS REFERENCE STANDARD-JEDEC, JESD22-A114, OPTICAL POWER OUTPUT(TX) 0.022 MW AND FIBER TYPE 62.5/125	e3	AMPLIFIER
HFBR-57E5APZ	Broadcom	TRANSCEIVER	SURFACE MOUNT	3.6 V		85 Cel	-40 Cel			PIN PHOTODIODE	50/125, 62.5/125, MMF	.019 mW	LC CONNECTOR	3.3 V	55.2 mm	13.4 inch		Fiber Optic Transceivers	8.5 mm	1308 nm	3 V	1270 nm		1380 nm			AMPLIFIER
AFBR-59F1Z	Broadcom	TRANSCEIVER	PANEL MOUNT, THROUGH HOLE MOUNT	3.6 V		85 Cel	-40 Cel			LED	POF	.298 mW		3.3 V						650 nm	3 V	635 nm		675 nm			AMPLIFIER
AFBR-59F2Z	Broadcom	TRANSCEIVER	PANEL MOUNT, THROUGH HOLE MOUNT	3.6 V		70 Cel	-40 Cel	200 Mbps	200 Mbps	LASER, LED	POF	.298 mW		3.3 V						650 nm	3 V	635 nm		675 nm			AMPLIFIER
AFBR-57E6APZ	Broadcom	TRANSCEIVER	BOARD/PANEL MOUNT	3.6 V	Tin (Sn)	85 Cel	-40 Cel			PIN PHOTODIODE	50/125, 62.5/125, MMF	.007 mW	LC CONNECTOR	3.3 V	55.2 mm	13.4 inch			8.5 mm	1308 nm	3 V	1270 nm		1380 nm	SFF-8047I, SFF-8472	e3	AMPLIFIER
AFBR-59E4APZ-LH	Broadcom	TRANSCEIVER	PANEL MOUNT, THROUGH HOLE MOUNT	3.6 V	Tin (Sn)	85 Cel	-40 Cel			LED, PIN PHOTODIODE	50/125, 62.5/125, MMF	.01 mW	LC CONNECTOR	3.3 V	48.19 mm	13.59 inch	DIP		9.8 mm	1308 nm	3 V	1270 nm		1380 nm	IT ALSO HAS REFERENCE STANDARD-JEDEC, JESD22-A114, OPTICAL POWER OUTPUT(TX) 0.022 MW AND FIBER TYPE 62.5/125	e3	AMPLIFIER
AFBR-59E4APZ-HT	Broadcom	SFF TRANSCEIVER	PANEL MOUNT, THROUGH HOLE MOUNT	3.6 V	Tin (Sn)					LED, PIN PHOTODIODE	50/125, 62.5/125, MMF	.02 mW	LC CONNECTOR	3.3 V	48.19 mm	13.59 inch	DIP		9.8 mm	1308 nm	3 V	1270 nm		1380 nm	OPTICAL POWER OUTPUT(TX) 0.022 MILLIWATT AND FIBER TYPE 62.5/125, MMF	e3	AMPLIFIER
AFBR-57E6APZ-HT	Broadcom	TRANSCEIVER	BOARD/PANEL MOUNT	3.6 V	Tin (Sn)	95 Cel	-40 Cel			PIN PHOTODIODE	50/125, 62.5/125, MMF	.007 mW	LC CONNECTOR	3.3 V	55.3 mm	13.4 inch			8.5 mm	1308 nm	3 V	1270 nm		1380 nm	MSA-SFF-8472, SFP-8074I	e3	AMPLIFIER
AFBR-57B4APZC	Broadcom	TRANSCEIVER	PANEL MOUNT	3.6 V		85 Cel	-40 Cel			VCSEL	62.5/125, MMF	.07 mW	LC DUPLEX CONNECTOR	3.3 V	57.8 mm	13.4 inch			8.5 mm	845 nm	3 V	805 nm	GR-63-CORE	865 nm	IT OPERATES FROM 800 TO 870 NM RECEIVER WAVELENGTH, IT OPERATES AT DATA RATE OF 50 MBAUD		AMPLIFIER, PIN PHOTODIODE

Fiber Optics - Transceivers

Fiber optic transceivers are electronic devices that are used in fiber optic communication systems to transmit and receive optical signals. They are designed to both transmit and receive data over a fiber optic network, allowing for two-way communication between devices.

Fiber optic transceivers typically consist of a transmitter, a receiver, and control circuitry. The transmitter converts electrical signals into optical signals, which are then transmitted over the fiber optic cable. The receiver converts the incoming optical signal into an electrical signal, which is then processed by the control circuitry.

Fiber optic transceivers use different technologies to transmit and receive optical signals, including:

1. Direct modulation: Direct modulation uses an LED or laser diode to directly modulate the optical signal in response to an electrical signal.

2. External modulation: External modulation uses an electro-optic modulator to modulate the optical signal in response to an electrical signal.

3. Coherent detection: Coherent detection uses a local oscillator to synchronize the optical signal with a reference signal, enabling precise phase and amplitude measurements of the optical signal.

Fiber optic transceivers come in different configurations and designs, depending on the application and the required performance. They can be integrated into a fiber optic network or mounted in a separate enclosure, depending on the application and the space available.