2 ohm Data Line Filters 5

Reset All

Part	Manufacturer	Filter Type	Construction	Maximum DC Resistance	Maximum Frequency	Material	Rated Current	Minimum Insulation Resistance	No. of Functions	Screening Level	Output Impedance (ohm)	Packing Method	Mounting Type	Rated Voltage	No. of Terminals	Sub-Category	Dimensions	Case Code	Maximum Operating Temperature	Attenuation At Maximum Frequency	Minimum Attenuation Frequency	Minimum Operating Temperature	Attenuation At Minimum Frequency	Terminal Finish	Inductance	Maximum Attenuation Frequency	Height	Width (mm)	Maximum Insertion Loss	Additional Features	JESD-609 Code	Minimum Frequency	Length
BKH1005LM182-T	Taiyo Yuden	FERRITE CHIP	Chip Bead	2 ohm	100 MHz	Ferrite	.2 A		1		1800 OHM	Tape, Paper	SURFACE MOUNT		2	Other Filters	L1XB.5XH.5 (mm)/L.0394XB.0197XH.0197 (inch)	0402	125 Cel			-55 Cel					.5 mm	0.5				100 MHz	1 mm
DLW43SH101XP2L	Murata Manufacturing	FERRITE CHIP		2 ohm			.17 A	10 Mohm	2	AEC-Q200		TAPE AND REEL	SURFACE MOUNT	50 V	4		L4.5XB3.2XH2.7 (mm)/L0.177XB0.126XH0.106 (inch)		125 Cel			-40 Cel		Tin (Sn)	100 uH		2.7 mm	3.2			e3		4.5 mm
FK2125T186AL-T	Taiyo Yuden	DATA LINE FILTER		2 ohm			.1 A	30 Mohm	1		50 OHM	TAPE AND REEL	SURFACE MOUNT	10 V	4		L2.0XB1.25XH1.0 (mm)/L0.079XB0.049XH0.039 (inch)		85 Cel	20 dB	50 MHz	-25 Cel	20 dB			500 MHz	1 mm	1.25	1 dB	T-TYPE CIRCUIT; CUT-OFF FREQUENCY 18 MHZ			2 mm
FK2125T256AL-T	Taiyo Yuden	DATA LINE FILTER		2 ohm			.1 A	30 Mohm	1		50 OHM	TAPE AND REEL	SURFACE MOUNT	10 V	4		L2.0XB1.25XH1.0 (mm)/L0.079XB0.049XH0.039 (inch)		85 Cel	20 dB	50 MHz	-25 Cel	15 dB			500 MHz	1 mm	1.25	1 dB	T-TYPE CIRCUIT; CUT-OFF FREQUENCY 25 MHZ			2 mm
744235101	Wurth Elektronik	DATA LINE FILTER		2 ohm			.15 A		2		5000 OHM	TR, EMBOSSED, 7 INCH	SURFACE MOUNT	60 V	4		L4.55XB3.22XH2.7 (mm)/L0.179XB0.127XH0.106 (inch)		125 Cel			-40 Cel		Tin (Sn) - with Nickel (Ni) barrier			2.7 mm	3.22		IMPEDANCE AT 10 MHZ	e3		4.55 mm

Data Line Filters

Data line filters are electronic filters that are used to filter out noise and interference from data communication lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired data signal to pass through with minimal distortion.

Data line filters use a combination of passive and active components, including resistors, capacitors, inductors, and op-amps, to filter out noise and interference from data communication lines. They can be designed for a wide range of communication standards, including Ethernet, USB, HDMI, and other data communication protocols.

Data line filters can be designed as low-pass filters, which allow low-frequency signals to pass through while attenuating high-frequency signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

Data line filters are commonly used in a variety of electronic systems, including computers, telecommunication equipment, medical equipment, and industrial control systems. They are also used in data centers and other applications where high-speed data communication is critical.