1 A EMI Mains Filters 10

Reset All

Part	Manufacturer	Filter Type	Rated Current	Minimum Insulation Resistance	Approvals (V)	High Pot	Maximum Leakage Current	Packing Method	Mounting Type	Rated Voltage	Dimensions	Maximum Operating Temperature	Minimum Operating Temperature	Terminal Finish	Manufacturer Series	Height	Width (mm)	Diameter (mm)	Additional Features	JESD-609 Code	Operating Frequency (Hz)	Length
TF0804S-01	TDK	SINGLE PHASE EMI FILTER	1 A						THROUGH HOLE MOUNT	50 V	D10.0XH6.0 (mm)/D0.394XH0.236 (inch)	105 Cel	-20 Cel		TF0804S-01	6 mm		10	INDUCTANCE 3 MICRO HENRY
FN406B-1-02	Schaffner Holding Ag	SINGLE PHASE EMI FILTER	1 A		UL; CSA; ENEC-14	2500 V	.002 mA		THROUGH HOLE MOUNT	250 V	L45.0XB15.0XH28.0 (mm)/L1.772XB0.591XH1.102 (inch)	100 Cel	-25 Cel			28 mm	15.0		MEDICAL VERSION; INDUCTANCE 12 MILLIHENRY		50/60Hz	45 mm
RN122-1-02	Schaffner Holding Ag	SINGLE PHASE EMI FILTER	1 A		UL; VDE				THROUGH HOLE MOUNT	250 V		125 Cel	-40 Cel			16.5 mm	27				50/60Hz	28 mm
B82722A2102N001	TDK	SINGLE PHASE EMI FILTER	1 A		UL; EN; IEC; VDE			TRAY	THROUGH HOLE MOUNT	250 V				TIN OVER NICKEL		13.3 mm	22.3			e3	50/60Hz	22.7 mm
B84110A0000A010	TDK	SINGLE PHASE EMI FILTER	1 A		UL; CSA; ENEC-10	2700 V	.5 mA		THROUGH HOLE MOUNT	250 V	L56.0XB30.0XH23.0 (mm)/L2.205XB1.181XH0.906 (inch)			TIN		23 mm	30.0		INDUCTANCE 10 MILLI HENRY	e3	50/60Hz	56 mm
2794123	Phoenix Contact	SINGLE PHASE EMI FILTER	1 A		UL; IEC; VDE				DIN RAIL MOUNT	250 V	L79.4XB25.0XH90.3 (mm)/L3.126XB0.984XH3.555 (inch)	100 Cel	-25 Cel			90.3 mm	25.0					79.4 mm
SN5-5501	KEMET Corporation	SINGLE PHASE EMI FILTER	1 A					BULK	THROUGH HOLE MOUNT			105 Cel	-25 Cel			7 mm		13
SSHB21HS-10145	KEMET Corporation	SINGLE PHASE EMI FILTER	1 A	100 Mohm	UL	500 V		TRAY	THROUGH HOLE MOUNT	250 V		130 Cel	-25 Cel			15.5 mm	23					26 mm
SSHB21HS-R10300	KEMET Corporation	SINGLE PHASE EMI FILTER	1 A	100 Mohm	UL	500 V		TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel			15.5 mm	23					26 mm
SSRH7H-M10108	KEMET Corporation	SINGLE PHASE EMI FILTER	1 A	100 Mohm	UL			TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel			12 mm	14.5					18 mm

EMI Mains Filters

EMI mains filters are electronic filters that are used to suppress electromagnetic interference (EMI) from mains power lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired power signal to pass through with minimal distortion.

EMI mains filters use a combination of passive and active components, including capacitors, inductors, resistors, and diodes, to filter out noise and interference from power lines. They can be designed for a wide range of power ratings and frequencies, depending on the application.

EMI mains filters can be designed as low-pass filters, which allow low-frequency power signals to pass through while attenuating high-frequency EMI signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

EMI mains filters are commonly used in a variety of electronic systems, including power supplies, motor drives, medical equipment, and industrial control systems. They are also used in residential and commercial buildings to suppress EMI noise from power lines and prevent interference with other electronic devices.