3 A EMI Mains Filters 15

Reset All

Part	Manufacturer	Filter Type	Rated Current	Minimum Insulation Resistance	Approvals (V)	High Pot	Maximum Leakage Current	Packing Method	Mounting Type	Rated Voltage	Dimensions	Maximum Operating Temperature	Minimum Operating Temperature	Terminal Finish	Manufacturer Series	Height	Width (mm)	Diameter (mm)	Additional Features	JESD-609 Code	Operating Frequency (Hz)	Length
ESP-03-221-D	Cosel	SINGLE PHASE EMI FILTER	3 A		UL; CSA; VDE; ENEC-10	2500 V	.05 mA		DIN RAIL MOUNT	250 V	L85.0XB39.0XH30.0 (mm)/L3.346XB1.535XH1.181 (inch)	85 Cel	-40 Cel		ESP	30 mm					60Hz	85 mm
ESP-03-221	Cosel	SINGLE PHASE EMI FILTER	3 A		UL; CSA; VDE; ENEC-10	2500 V	.05 mA		CHASSIS MOUNT	250 V	L85.0XB39.0XH30.0 (mm)/L3.346XB1.535XH1.181 (inch)	85 Cel	-40 Cel		ESP	30 mm					60Hz	85 mm
ESP-03-222-D	Cosel	SINGLE PHASE EMI FILTER	3 A		UL; CSA; VDE; ENEC-10	2500 V	.5 mA		DIN RAIL MOUNT	250 V	L85.0XB39.0XH30.0 (mm)/L3.346XB1.535XH1.181 (inch)	85 Cel	-40 Cel		ESP	30 mm					60Hz	85 mm
ESP-03-222	Cosel	SINGLE PHASE EMI FILTER	3 A		UL; CSA; VDE; ENEC-10	2500 V	.5 mA		CHASSIS MOUNT	250 V	L85.0XB39.0XH30.0 (mm)/L3.346XB1.535XH1.181 (inch)	85 Cel	-40 Cel		ESP	30 mm					60Hz	85 mm
FMW-65-0001	Schurter Ag	THREE PHASE EMI FILTER	3 A		UL; IEC; VDE; ENEC-10	3000 V	.5 mA		PANEL MOUNT	440 V	L66.0XB51.0XH43.0 (mm)/L2.598XB2.008XH1.693 (inch)	100 Cel	-25 Cel			43 mm	51.0		INDUCTANCE 1 MILLIHENRY		50/60Hz	66 mm
B84111F0000B030	TDK	SINGLE PHASE EMI FILTER	3 A		UL; CUL; ENEC-10	2700 V	.5 mA		PANEL MOUNT	250 V	L43.5XB35.0XH26.0 (mm)/L1.713XB1.378XH1.024 (inch)					26 mm	35.0				50/60Hz	43.5 mm
744841330	Wurth Elektronik	SINGLE PHASE EMI FILTER	3 A		ENEC-10; IEC; VDE			TRAY; PAPER	THROUGH HOLE MOUNT	250 V	L15.5XB7.5XH17.5 (mm)/L0.61XB0.295XH0.689 (inch)	125 Cel	-40 Cel	Tin/Silver/Copper (Sn/Ag/Cu)		17.5 mm	7.5			e1	50Hz	16 mm
B84111A0000A030	TDK	SINGLE PHASE EMI FILTER	3 A		UL; CSA; ENEC-10	2700 V	.5 mA		PANEL MOUNT	250 V	L50XB45XH22.3 (mm)					22.3 mm	45		TAB CONNECTORS ON FACE ENDS, LATERAL MOUNTING TABS		50/60Hz	50 mm
B84115E0000B030	TDK	SINGLE PHASE EMI FILTER	3 A		UL; CSA; ENEC-10	2700 V	.5 mA		PANEL MOUNT	250 V	L63.5XB50.8XH38.1 (mm)					38.1 mm	50.8		TAB CONNECTORS ON LOAD SIDE, IEC CONNECTOR ON LINE SIDE		50/60Hz	63.5 mm
SC-030-E150JH-P	KEMET Corporation	SINGLE PHASE EMI FILTER	3 A	100 Mohm	UL	500 V		TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel			14.5 mm		31
SSHB10HS-30006	KEMET Corporation	SINGLE PHASE EMI FILTER	3 A	100 Mohm	UL	500 V		TRAY	THROUGH HOLE MOUNT	250 V		130 Cel	-25 Cel			15.5 mm	17					22 mm
SSHB21H-R30050	KEMET Corporation	SINGLE PHASE EMI FILTER	3 A	100 Mohm	UL	500 V		TRAY	THROUGH HOLE MOUNT	250 V		130 Cel	-25 Cel			15.5 mm	23					26 mm
SSRH24NH-30145	KEMET Corporation	SINGLE PHASE EMI FILTER	3 A	100 Mohm	UL			TRAY	THROUGH HOLE MOUNT	250 V		120 Cel	-25 Cel			18 mm	25.5					25.5 mm
10510	Murrelektronik	THREE PHASE EMI FILTER	3 A		EN	2700 V			DIN RAIL MOUNT	440 V						107 mm	39				50-60	65 mm
S8V-NFS203	Omron	SINGLE PHASE EMI FILTER	3 A	100 Mohm	EN; CSA; IEC; UL		1 mA		PANEL MOUNT	250 V		85 Cel	-40 Cel			90 mm	32				50/60Hz	90 mm

EMI Mains Filters

EMI mains filters are electronic filters that are used to suppress electromagnetic interference (EMI) from mains power lines. They are designed to provide a high level of attenuation of unwanted frequencies while allowing the desired power signal to pass through with minimal distortion.

EMI mains filters use a combination of passive and active components, including capacitors, inductors, resistors, and diodes, to filter out noise and interference from power lines. They can be designed for a wide range of power ratings and frequencies, depending on the application.

EMI mains filters can be designed as low-pass filters, which allow low-frequency power signals to pass through while attenuating high-frequency EMI signals, or as band-stop filters, which block a specific range of frequencies while allowing other frequencies to pass through. They can also be designed with multiple stages of filtering to provide increased attenuation of unwanted frequencies.

EMI mains filters are commonly used in a variety of electronic systems, including power supplies, motor drives, medical equipment, and industrial control systems. They are also used in residential and commercial buildings to suppress EMI noise from power lines and prevent interference with other electronic devices.